UV light curing machine and UV coating equipment applicable scope is wide, such as plane or three-dimensional artifacts require UV coating products all available, such as cabinet doors and Windows, furniture, handicrafts, jewelry, plastic pieces, helmets, artificial stone, sanitary ware, etc. This Oven is normal temperature oven it is forbidden to bake inflammable and explosive/volatile and corrosive materials. Items placed the oven should not be too crowded, so that the cold and hot air convection from blocking, to maintain uniform temperature
Uv Curing Oven,Uv Curing System,Automatic Led Uv Curing Oven Shenzhen Heng Yi Jia Technology Co., Ltd. , https://www.spraycoatingline.com
1. When the crop is watered, the quantitative fertilizer is dissolved in the ditch and infiltrated into the soil around the root of the crop with the watering. This method wastes a lot of fertilizer, and is easy to leak and leak in the channel. In the deep layer that the roots of the crop cannot reach, it will also infiltrate part of the fertilizer and cause waste. The advantage is that it is simple to use, saves labor and time, and has a small amount of labor. This method can be used when the fertilizer source is sufficient, the area of ​​growing vegetables is large, and labor conflicts are prominent. It can be used as the preferred method of top dressing when large areas of vegetables have severe fat deficiency symptoms.
Second, after the crop is poured into water or after the rain, the soil is suitable for the soil, and when it is able to go to the field, the quantitative fertilizer is applied to the crop surface or the crop line. This method is also relatively simple, but there is still some fat loss in the fertilizer, especially ammonium bicarbonate is very volatile, can not be used; ammonium sulfate, urea and potassium sulfate can be applied, but only in the field is not convenient, crops need Use when the fertilizer is more urgent.
3. Buried in the crops, ditching and digging between the rows, applying the quantitative fertilizer, and then filling the soil. This method is less wasteful and economical, but it is labor-intensive, labor-intensive, and inconvenient to operate. Pay attention to safety when applying. The buried fertilizer ditch and pit should be more than 10 cm from the base of the crop stem. If it is too close to the root, It is easy to damage the root system. Due to the concentration of fertilizer and the high concentration, this method should not be used in the summer when crops are vigorously growing and water is needed, and it cannot be used in the critical period of crop water demand. Generally, in the winter idle season, when the labor force is sufficient and the amount of crop growth is small, this method can be used to gradually decompose the buried fertilizer and continuously supply the crop. However, in actual production, the peak of crop growth is often the peak of fertilizer demand. Therefore, the method of burying is often used at higher temperatures. In order to prevent negative effects, water must be watered after burying to reduce the concentration of fertilizer applied.
IV. Facility pursuit In recent years, with the development of vegetable production technology in protected areas, the matching drip irrigation technology has been widely used, and the fertilization method has been on the track of automation. Specific Methods dressing drip irrigation facilities are: mounted fertilizer in water entering the drip director portion, fertilizer is dissolved in the fertilizer, a suction pipe is inserted into the drip director's filter fertilizer, the fertilizer can automatically enter the water with the crop roots In the surrounding soil. Since mulching, fertilizer hardly volatile, no loss, although concentrated fertilizer, but small concentrations, and therefore is safe and labor-saving, very good. This is a more scientific and highly promising method of topdressing, only to carry out strict film mulching, and must be equipped with matching drip irrigation and tap water equipment.
V. foliage foliage is Yemianpenfei. Facilities horticulture vegetables, due to the artificially created environments easier to meet the requirements of the environmental conditions of the crop, vegetables showed fast growth, high yield, results and more features. Lack of nutrient management in addition to pay attention to timely fertilizer, can also be combined with spraying, many times foliar application to supplement crops. This method is a cost-effective fertilization method because it has less dosage and quick fertilizer efficiency, and can avoid the fixation of fertilizer by soil. It can be used in the case of obvious deficiency and root senescence in the late stage of crop growth, and it can show its effect. In addition to urea, potassium dihydrogen phosphate, potassium sulfate, potassium nitrate, compound fertilizer and other commonly used large amount of elemental fertilizers, in recent years, many manufacturers in various places have developed suitable for foliar application. A large number of elements plus trace elements or fertilizers containing a variety of amino acid ingredients, such as spray Shibao, plant protection, farm music and so on. However, it must be noted that the basic nutrients required for the growth and development of vegetables are mainly derived from the base fertilizer and other methods of topdressing fertilizers. The external top dressing can only be used as an auxiliary measure.
Vegetable topdressing methods are more favorable and have a good grasp
After sowing and planting vegetables, in order to meet the needs of their growth and development, more top dressing is often required. The amount of topdressing generally accounts for 1/3 or more of the total fertilization amount of the crop during the whole growth period. Here are a few common topdressing methods, enumerating their advantages and disadvantages, for reference by farmers.
ã€Comment】 ã€Print this article】 ã€Close this page】 ã€Large, medium and small】