Tungsten Carbide End Mills-Single Flute End Mills
Material:Carbide
Flute:Single
Model Number:End mill
Single Flute End Mills,Single Flute Milling Cutter,Cut End Mills Single Flute,Cutter Tools For Aluminum Changzhou Bomitools Co.,Ltd. , https://www.bomitools.com
Coating:DLC
Product Name:Single Flutes End Mills High Speed Cutting
Suitable for:Carbon Steel
Application:CNC Process
Usage:General High Speed Cutting
Controlling Mode:CNC Tooling System
Material:Carbide, Tungsten Cobalt Alloy
Coating:AlTiN, TiAIN, TiCN, Tin
Product Name:Tungsten Carbide Solid End Mill Cutters
Main Using Purpose:Carbide Body for Drill Bits/ Endmills / Reamers
Service:OEM/ODM
Type:End mill
Cobalt Percentage:From 3% to 30% Based on Different Grades
Grain Sizes Selection:Ultra Fine, Fine, Medium, Coarse
Grades:K10/K20/K30/K40/Yl10.2/Yg6/Yg6X/Yg8/Yg10X/Yl10.2
Surface Finishing:Polished and Unpolished
Nitrogen decompression valve failure can be replaced with oxygen valve it
Nitrogen valve failure, the temporary use of oxygen valve instead? For this problem, we must first know what are the nitrogen valve and oxygen valve. Nitrogen valve: Nitrogen valve is the use of control valve body opening and closing pieces of the opening to regulate the flow of media, media pressure will be reduced at the same time by virtue of the role of the pressure valve to adjust the opening and closing pieces of the opening, the valve After the pressure remained within a certain range, and in the valve body or after injection of cooling water, the medium temperature decreases, this valve is called decompression valve. Oxygen valve work by the valve pressure control. When the pressure sensor detects the valve pressure indication increases, the valve opening of the pressure reducing valve decreases; when the pressure reducing valve is detected to reduce the pressure reducing valve valve opening increases to meet the control requirements. This type of valve in the pipeline should be generally horizontal installation. For water, steam, air medium pipeline. Therefore, as long as the parameters are proper, it should be possible, but the cost is higher, because ordinary oxygen pressure relief valve will be banned, so it is more expensive than nitrogen! However, there are some exceptions, which are used on low nitrogen or Pure nitrogen, the request is relatively high! So nitrogen valve and oxygen valve do not mind mixing, it is best to what media to use what pressure reducing valve, after all, it is no shortage of product era!
Specification
It can be divided into 3 categories, normal end mill, ball end cutter, ball nose end mill cutters.
Cutting D (mm)
Shank D(mm)
Overal length (mm)
Flute
Flute
Flute
Angle
Angle
Angle
1.0
1.0
50
2
3
4
55°
60°
65°
1.5
1.5
50
2
3
4
55°
60°
65°
2.0
2.0
50
2
3
4
55°
60°
65°
2.5
2.5
50
2
3
4
55°
60°
65°
3.0
3.0
50
2
3
4
55°
60°
65°
3.5
3.5
50
2
3
4
55°
60°
65°
4
4
50
2
3
4
55°
60°
65°
5
5
50
2
3
4
55°
60°
65°
6
6
50
2
3
4
55°
60°
65°
8
8
60
2
3
4
55°
60°
65°
10
10
75
2
3
4
55°
60°
65°
12
12
75
2
3
4
55°
60°
65°
14
14
100
2
3
4
55°
60°
65°
16
16
100
2
3
4
55°
60°
65°
18
18
100
2
3
4
55°
60°
65°
20
20
100
2
3
4
55°
60°
65°