Members of the Standards Committee and relevant units : According to the 2009 standard revision plan and the work arrangement of the Standardization Committee, the research meeting of the National Abrasives Standardization Technical Committee was held at the Fengyuan Hotel in Zhengzhou on November 18 and 19-22, 2009. The main topics of the meeting were: 1. Review the work report of the Standards Committee in 2009; 2. Review the 8 drafts for review; 3. Review the draft safety standards for abrasives; 4. Negotiate the work plan and arrangements for the 2010 Standards Committee 2010 standard revision task. In order to ensure the smooth completion of the 2009 standard review work and the orderly development of the standardization work in 2010, the Committee and the members of the clubs are required to attend the meeting. If there are special reasons for not attending, you can send a comrade who can represent the opinions of the unit at your discretion. The relevant matters of the meeting are hereby notified as follows: one. Conference content 1. Review the work report of the 2009 Standards Committee 2. Standard review work (1) General Abrasive Subcommittee 1 Single crystal corundum chemical analysis method (revised) 2 Ordinary abrasives Determination of capillary phenomenon (development) (2) Technical Committee for General Abrasives and Silicon Carbide Special Products 1Consolidation Abrasives Deep and Slow-feeding Grinding Wheels (Revised) 2 silicon carbide special products silicon carbide thermocouple protection tube (revised) (3) Superhard abrasives and products subcommittee 1 super hard abrasive technical conditions of synthetic diamond (revised) 2 diamond sawing tool with metal bond (developed) 3 hydroxy iron powder for diamond products (developed) 4 plastic connection sintered diamond beaded wire saw (developed) 3. Review draft safety standards for abrasive tools (1) Consolidation abrasives Safety rules (draft draft) (2) Superhard abrasives Safety rules (draft draft) (3) Coated abrasives Safety rules (draft draft) 4. Discuss the 2010 work plan of the Standardization Committee and arrange the 2010 standard revision and revision tasks (1) Discuss the preparation of the 2010 standard revision plan. (2) According to the standard revision plan issued by the National Standardization Administration Committee and the Machinery Industry Federation, arrange the tasks and progress of the 2010 standard revision and revision work. Second, the meeting schedule Superhard Materials and Products Subcommittee November 18th November 19th - November 22nd Full-day meeting Other subcommittees November 19th November 20th - November 22nd Full-day meeting Third, the meeting place Songzhai South Street, North Section of Nanyang Road, Zhengzhou Zhengzhou Fengyuan Hotel Switchboard: 0371- 66771188 Take the No. 4, No. 8 or No. 504 bus from the train station, get off at Nanzhai Road Zhangzhai Station, walk 300 meters to the east; take a taxi from the train station to Fengyuan Hotel for about 20 minutes, cost about 18 Yuan or so. From the airport, take the civil aviation bus (cost 15 yuan) to the Civil Aviation Hotel, then take a taxi from the Civil Aviation Hotel to the Feng Paradise Hotel. The cost is about 20 yuan. It takes about 1 hour by taxi from the airport to Fengyuan Hotel. The estimated cost is 100-150 yuan. Fourth, meeting charges This meeting will charge a conference fee of 800 yuan. Accommodation and accommodation are arranged in a unified manner , and the expenses are self-care (Note: In order to facilitate the smooth progress of the review, the representatives of Zhengzhou area are required to reunite the residence) . Five, matters needing attention 1. In order to facilitate the preparation of meeting materials, arrange meeting services, and invite all units to fill in the receipts (Annex 1) after receiving the meeting notice, and must return to the Secretariat of the Standards Committee by express mail or fax before November 5. Contact information of the Secretariat of the Standards Committee: Contact number: 0371-67614280,67657910 Fax: 0371-67614280,67658535 Address: 121 Huashan Road, Zhengzhou City, China Postcode: 450013 Contact: Wang Weitao, mobile phone Contact: 翟曼丽, mobile phone Contact: Zhong Yanzhen, mobile phone 2. Arrangements can be arranged after 8 pm on November 22, and delegates who need to book a return ticket in advance must indicate the return trip, time and arrival location in the return receipt. Annex 1: Conference receipt October 20, 2009
We diviided the led light according to the using eviiroment. Most of our product is the commercial LED Lighting
Commercial lighting is a term used to describe lighting that is used in commercial spaces, including auto dealerships, distribution centers, churches, factories, offices, and warehouses. Unlike residential lighting, commercial lighting is made to withstand more abuse and has a longer lifespan.
While the focus of residential lighting is often on aesthetics, commercial lighting is task orientated. Commercial lighting systems are designed based on what the application is. For example, in an office-type setting, you may see task lighting, which illuminates specific areas where employees need concentrated light to be able to perform their jobs.
Wall Light,Up Down Wall Light,Mr16 Wall Light,Wall Light Fixture Led Jiangmen Dilin Lighting High-Tech Co., Ltd. , https://www.jmdilinlight.com
Attachment Download: 2009 Abrasives Standardization Work Conference and Standards Review Conference Receipt
Notice on holding the 2009 Abrasives Standardization Work Conference and Standards Review Meeting
Abstract Committee members and relevant units: According to the 2009 Standard Revision Plan and the work arrangement of the Standards Committee, the National Abrasive Mill will be held at the Fengyuan Hotel in Zhengzhou on November 18th and 19th, 22nd, 2009. Work conference with standardization technical committee. meeting...