In today's rapid development of the coatings industry, all brands of paints want to take the lead. However, among many coatings, water-based coatings are still popular. This is a new type of coating. It uses its own advantages to make it widely accepted by many people in the industry. Although this is the case, there are still many People don't have a correct understanding of water-based paints, so there are some misunderstandings when using them. The following is a good introduction to the use of water-based paints. 1. Adjust the paint to a suitable spray viscosity with clean water and measure with a coating-4 viscometer. The appropriate viscosity is generally 20 to 30 seconds. If there is no viscometer at one time, visual method can be used: stir the paint with a rod (iron rod or wooden stick) and pick it up to a height of 20 cm to stop and observe. If the paint liquid is continuous in a short time (a few seconds), It is too thick; if it is off the edge of the barrel, it is too thin; when it is just 20 cm high, the paint liquid is in a straight line, and the instantaneous flow is turned into a downward drop. This viscosity is more suitable. 2. The air pressure is preferably controlled at 0.3-0.4 MPa (3-4 kgf/cm2). If the pressure is too small, the spray liquid will be atomized, and the surface will form pitting. If the pressure is too large, it will sag and the paint mist will be too large, which will waste materials and affect the health of the operator. 3. The distance between the nozzle and the object surface is generally 300-400 mm. It is easy to sag too close; the paint mist is not uniform too far, and it is prone to pitting, and the nozzle is far away from the object surface and the fog is scattered on the way. The specific size of the distance should be appropriately adjusted according to the type of paint, viscosity and pressure. Slow drying paint spraying distance can be a little farther, quick-drying paint spraying, the distance can be closer; when the viscosity is thick, it can be closer, when the viscosity is thin, the distance can be farther; when the air pressure is large, the distance can be farther, the pressure can be closer; the so-called A little closer is a small adjustment between 10 mm and 50 mm. If it exceeds this range, it is difficult to obtain a desired paint film. 4, the spray gun can be moved left and right, up and down, preferably at a speed of 10-12 m / min. The nozzle should be sprayed straight to the surface, to minimize the oblique spray. When spraying to both ends of the object surface, the hand of the trigger of the spray gun should be loosened quickly to reduce the paint mist, because the two ends of the object surface often need to be sprayed twice or more, which is the most likely place for sag. 5. When spraying, press the next one to hold 1/3 or 1/4 of the previous one, so that there will be no leakage. When spraying the quick-drying paint, it is necessary to spray it in sequence. The effect of refilling is not ideal. 6. When spraying in an open space, pay attention to the wind direction (not suitable for operation in high winds). The operator should stand in the downwind direction to prevent the paint mist from being blown onto the sprayed paint film to create an unsightly grainy surface. 7, the order of spraying is: first difficult and easy, first and then outside. After the height is high, the small area is small. This will not cause the spray mist of the post-spray to splash onto the sprayed paint film and destroy the sprayed paint film. Any object and thing is not perfect, water-based paint is the same, although it has its own advantages, but there are still many problems, but we can continue to improve through the above processes and technologies, some problems can be very good Prevention. Cheaper Surface Protection Floor Shield Surface Shield Pad,Temporary Wood Floor Protection,Cover Fleece For Floorguard,Carpet Protector Floor Mats Suzhou Surface Protective New Material Technology Co.,Ltd , https://www.surfaceprotective.com
Waterborne paint spraying construction operation skills
Jc001.load('iframe') JIFrame.create({ 'url' : '/go.php?action=ads&iframeHeight=250&isIframe=1&key=%CD%BF%C1%CF&pos_id=jc001_news_detail_30&reqkey=1&style=margin%3A15px+15px+ 25px+0%3B+height%3A255px%3Bwidth%3A255px%3B+float%3Aleft%3B', 'height' : 250 })